Following a flood or escape of water, traditional drying methods are not always the most appropriate techniques for drying the structure of a building.
Injection drying is an alternative option which complements the traditional systems that can be used to accelerate the drying process in many situations. This is achieved by introducing a flow of dry air directly into wet cavities behind walls, floors, ceilings or any other areas where moisture is trapped and inaccessible.
Rainbow utilises turbine technology for their injection drying programme as it is specially
designed to address trapped moisture within a construction. A desiccant unit situated in the top of the turbine produces very dry warm air through moisture extraction by an internal desiccant wheel. This dried air is then ducted to the inlet of a turbine unit located in the base of the unit. This pressurises the dried air to circa 260mb (3.7 PSI) which is then injected into the cavity. Increasing the pressure also causes an increase in temperature in the air.
The heat energy carried by the air then promotes evaporation of the moisture which is vented back into the environment to be processed out of the building.
This advanced drying technique is unobtrusive and quiet. It avoids the need for costly strip out, removal and reinstatement of building materials such as concrete floors and walls.
By utilising injection drying techniques, major strip out, which can be devastating to property owners and tenants, not to mention very expensive, can often be avoided. The injection drying system can be installed quickly and allows people to continue to use the affected rooms without disruption. This drying regime also often avoids the need for alternative accommodation and costly removal and replacement for insurance companies.
Many modern property techniques are complex in their construction. The need to insulate modern day building structures can produce conditions where surface drying techniques are unable to eradicate trapped moisture completely.
In the event of a flood or escape of water, moisture can be forced into insulated areas and cavities of a building structure. In many cases there is no easy path for this moisture to return to the environment.
If left unaddressed the moisture could later migrate to other areas, causing further damage to previously restored or unaffected areas.
This process can sometimes take months before issues start to materialise and problems occur.
The injection drying system provides a drying solution that targets trapped moisture within building interfaces including floating floors. To gain access to these areas it is necessary to open paths to remove the trapped moisture. This process often involves drilling into the building construction to enable dry air to be forced through pipes to the affected area. The forced air then collects the the construction leaving the affected area free of moisture and structurally sound.
It is essential that air movement is created throughout the affected area as with all drying techniques, the air is used to carry released moisture away from affected areas. This may require certain elements of the structure to be compromised in order to remove the moisture.
An initial site assessment and scope of works is needed to identify these requirements and in
particular care should be taken to avoid damaging service installations, such as electrics and pipes hidden within the cavities.
Thermal imaging surveys can assist in locating these elements and care should also be taken not to damage the DPC of the structure.
Once an injection drying system has been installed it is monitored using the vented air quality as a drying guide. As the dry air is forced through the construction, moisture is collected meaning the specific humidity of the vented air is increased.
The %RH of this vented air would also be high when measured. The graphs above are typical of the last days of the drying cycle of a floating floor.
The injection drying system is also very effective when addressing wooden floating floors, dot and dab walls, stud partitions and external wall cavities.
Typically one machine can address 35m2 of concrete floating floor, a typical construction in UK properties. The internal partitions are then created on top of this single slab, and as such a leak can easily migrate through the floor construction and
affect other areas on the slab.
Injection drying provides a very robust and credible addition to the portfolio of drying regimes to the Damage Management industry. Its use in UK restoration projects has seen an increase over recent years due to its flexible nature, speed of drying and cost effective programme on many projects where the trapped moisture is inaccessible following water damage.
Contact your local Rainbow office for further information on injection drying.
Receive a complimentary price quote for cleaning services that will fit your needs and your budget
Call us at 01322 662277 or 01322 515961
Our services are delivered 24 hours a day through a national network of over 70 branches strategically located across the country, providing a local service efficiently, reliably and cost effectively. We can be on-site in an emergency situation within 2 hours anywhere in the country, commencing work, minimizing the risk of secondary damage and returning homeowners lives and commercial businesses back to normal with the minimal disruption and downtime.